Post Reply 
 
Thread Rating:
  • 1 Votes - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Replicator 1,2,2x
12-15-2013, 01:43 AM
Post: #1
Replicator 1,2,2x
Result of making 3D parts by using Replicator 1,2,2x.
Find all posts by this user
Quote this message in a reply
12-16-2013, 10:13 PM (This post was last modified: 12-16-2013 10:15 PM by sho.)
Post: #2
Coreboard
I printed "coreboard" about 3 month ago.


Printer: Replicator2

Print options:
Raft:Yes
Supports:yes
I used default Profile "LOW". But, I changed speed faster.
Speed while Extruding: 150mm/s
Speed while Traveling: 200mm/s

Quality is same.
Infill: 10%
Shells: 2
Layer Hight 0.3 mm
Temperature: 230℃

Printed time:about 2hours
Result:
Printed:yes
use:difficult. Because of the shape of pin and hole.
Hole is small, and pin is fragile.
I wrote about this at here. Wink


Attached File(s) Thumbnail(s)
   

.obj  coreboardv001.obj (Size: 785.51 KB / Downloads: 172)
Find all posts by this user
Quote this message in a reply
12-17-2013, 12:14 AM (This post was last modified: 12-22-2013 11:05 PM by sho.)
Post: #3
RE: Replicator 1,2,2x
I printed these parts about 3 month ago. I will write detail soon.
   
Find all posts by this user
Quote this message in a reply
01-02-2014, 03:10 AM
Post: #4
RE: Replicator 1,2,2x
I took out Replicator2 from my home. So, I could start making Micropede by Replicator2 at here(My apartment in Tsukuba).

At first, I tryed to make "small version" of Micropede.
Please see Micropede131225a.skp or Micropede131225a.png
I'm trying to make this.

At first, I printed Micropede131225Chassis3.obj at "Low resolution".
But, It was very fragile (IMGP9149cs.jpg ).
So, I will try to redesign chasis.


Attached File(s) Thumbnail(s)
           

.skp  Micropede131225a.skp (Size: 2.71 MB / Downloads: 173)
.obj  Micropede131225Chassis3.obj (Size: 348.95 KB / Downloads: 145)
Find all posts by this user
Quote this message in a reply
01-05-2014, 01:50 AM (This post was last modified: 01-05-2014 02:31 AM by sho.)
Post: #5
MP_MOTORCOVER
I printed MP_MOTORCOVER

Print profile
Data:MP_MOTORCOVER_v002r2.obj
Printer:Replicator2
Resolution:Standard
LayerHeight:0.2mm
Raft:yes
Support:yes
Print time:12m

Result:
worked. But, I have to change the front and back of gearmotor. Please see the 2nd picture. The left motorcover is I printed. This is no problem to use, but, I will repair.

   
   


Attached File(s)
.skp  MP_MOTORCOVER_v002r2.skp (Size: 36.63 KB / Downloads: 166)
.obj  MP_MOTORCOVER_v002r2.obj (Size: 29.1 KB / Downloads: 143)
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)